Silage smell check: freshly chopped forage being packed into a silage clamp, where fermentation quality is later judged by odour

Open a bale or cut into a silage clamp and the first thing you notice is the smell. Long before a lab report arrives, your nose has already told you a great deal about what happened inside that silage over the past weeks. A clean, faintly sour aroma usually means the fermentation went well. A smell of rancid butter, nail polish, burnt sugar or ammonia means something went wrong, and each of those odours points to a different problem with a different cause.

Smell is not a replacement for laboratory analysis, but it is the fastest and cheapest diagnostic tool a farmer has. Learning to read it properly helps you decide which silage to feed to which animals, when to send a sample to the lab, and what to change at the next harvest. This guide explains what each common silage smell means, which compound causes it, what the typical laboratory values look like, and how to prevent the problem next time.

Why Silage Smells the Way It Does

Silage is preserved by fermentation. Once forage is packed and sealed, bacteria convert plant sugars into acids, and those acids lower the pH until the crop is stable. In an ideal fermentation, the main product is lactic acid, which is strong enough to drop pH quickly and is almost odourless. That is why the best silage often smells surprisingly mild, slightly sour or faintly earthy rather than strongly of anything at all.

Other microbes produce other compounds, and many of those are volatile, which means they evaporate easily and reach your nose. Acetic acid smells of vinegar. Butyric acid, produced by clostridial bacteria, smells rancid or like vomit. Yeasts produce ethanol, which gives an alcoholic or sweet, fruity note. Protein breakdown releases ammonia and amines. Heat damage creates the caramel and tobacco odours of the Maillard reaction. Each smell is effectively a chemical fingerprint of the microbes that were active in the silage.

That is the key idea behind smell-testing. You are not judging whether silage smells “nice.” Some pleasant smells, such as sweet, fruity or butterscotch, actually signal wasteful fermentations, while some unpleasant-sounding ones, such as a mild vinegar note in silage treated with a Lactobacillus buchneri inoculant, can be perfectly normal.

How to Smell-Test Silage Properly

A few habits make smell-testing more reliable and safer. Fermentation needs time to settle, so wait until the silage has been sealed for at least three to four weeks before judging it. Take samples from several places, because a clamp or a batch of bales is rarely uniform: the shoulders of a clamp, the area under a damaged sheet and the outer layer of a bale often smell different from the core.

Do not bury your nose in a handful of silage and inhale deeply. Ian Williams, a forage specialist writing in Rural News, warns that some silages may contain spores harmful to human health. A safer method is to place a sample on a flat surface and waft the air towards your nose with your hand, as a chemist would.

Finally, never rely on smell alone. Combine it with colour, texture and temperature. Slimy texture, dark colour and warmth at the face all add information that smell cannot give on its own, and a laboratory fermentation analysis is the only way to put numbers on what you suspect.

Silage Smell Chart: What Each Odour Means

The table below summarises the most common silage odours, drawing on guidance from the Ontario Ministry of Agriculture, Food and Agribusiness, Hoard’s Dairyman and Rural News.

Smell Main Compound Likely Cause Verdict
Mild, slightly sour or earthy Lactic acid Efficient lactic fermentation Good
Light vinegar (inoculated with L. buchneri) Acetic acid Intended conversion of lactic to acetic acid Normal; improves stability
Strong vinegar, often yellow Acetic acid Inefficient fermentation; low sugar or wet crop Acceptable but wasteful
Rancid, vomit, rotten meat, fishy Butyric acid, amines Clostridial fermentation; soil or wet crop Poor
Alcohol, sweet, fruity, butterscotch Ethanol and other yeast products Yeast activity Wasteful; heats easily
Nail polish remover, acetone Esters Alcohols reacting with acids; often after air exposure Warning of heating
Sharp, sweet Propionic acid Low-sugar forage or propionic acid additive Usually acceptable
Ammonia Ammonia Protein breakdown; clostridia or high pH Poor
Caramel, burnt sugar, tobacco Maillard reaction products Heating from trapped oxygen; often too dry Reduced protein value
Musty, mouldy Mould metabolites Oxygen ingress; poor sealing or slow feed-out Poor; discard visibly mouldy feed

Mild, Slightly Sour or Earthy: A Good Fermentation

Well-fermented silage often has little smell at all. Lactic acid, the product you most want, is nearly odourless, so a clean silage may smell faintly sour, slightly sweet or earthy, with at most a light vinegar note. Hoard’s Dairyman describes the normal smell as slightly sweet or mildly vinegary. If you find this kind of silage, the fermentation probably went the way it should, although a lab test is still worthwhile to confirm dry matter and nutrient values.

Vinegar: Acetic Acid, Good or Wasteful Depending on Context

A vinegar smell comes from acetic acid, and its meaning depends on how the silage was made. If maize or grass was treated with an inoculant containing Lactobacillus buchneri, a light vinegar smell is expected. These bacteria deliberately convert some lactic acid into acetic acid later in storage, because acetic acid inhibits the yeasts that cause silage to heat once it is opened. In that case, vinegar is a sign the inoculant has done its job.

In untreated silage, a strong vinegar smell, often with a yellow colour, usually means a less efficient fermentation dominated by other bacteria, typically when the crop was low in sugar or too wet. Ontario’s guidance flags acetic acid above 3 to 4 percent of dry matter as a concern, especially when lactic acid is low, and suggests lactic acid should make up more than 65 to 70 percent of total acids, with a lactic to acetic ratio of at least 3 to 1. Such silage is usually safe to feed, but more dry matter was lost during fermentation and intake may be lower.

Rancid, Vomit or Rotten Meat: Butyric Acid and Clostridia

This is the smell nobody forgets. A rancid, putrid, fishy or vomit-like odour comes from butyric acid, produced by clostridial bacteria. Clostridia come mainly from soil, and they thrive in wet silage where the pH falls too slowly. They convert sugars and lactic acid into butyric acid and break down protein into ammonia and amines, so the silage loses energy and protein and becomes far less palatable. Hoard’s Dairyman notes that this silage is often yellow-green or brown and slimy.

Butyric silage is mainly a grass and legume problem, rarely a maize one. Ontario’s guidance attributes it to soil contamination from cutting or raking too close to the ground, tyre-packed soil, rain splash or late manure application, and to forage ensiled too wet, above about 70 percent moisture. It also cites limits on butyric acid intake for dairy cows: under 50 g per day for fresh cows, under 150 g for early-lactation cows, and under 250 g for other lactating cows, because high butyric intake is linked to poor appetite and ketosis. In practice, butyric silage is best kept away from fresh and high-yielding cows and fed, if at all, in small amounts to less sensitive stock.

Alcohol, Sweet, Fruity or Butterscotch: Yeasts at Work

Many people assume a sweet, fruity or butterscotch smell means good silage. It does not. These odours usually come from ethanol and related compounds produced by yeasts. Yeasts compete with lactic acid bacteria for sugar, and they burn dry matter in the process, so silage that smells strongly of alcohol has generally suffered higher fermentation losses. Rural News describes alcohol, sweet, fruity, buttery and butterscotch smells as signs of yeast activity before maize is fully fermented.

High-yeast silage is also prone to heating and spoilage once it is opened, because yeasts are usually the first organisms to start breaking down silage when air returns. Ontario’s guidance notes that high-ethanol silage can occasionally cause off-flavours in milk. Feeding it promptly after removal from the face, and managing the face so that each layer is exposed to air for as short a time as possible, limits the damage.

Nail Polish or Acetone: Esters and a Warning Sign

A sharp, solvent-like smell resembling nail polish remover comes from esters, which form when alcohols react with silage acids. Hoard’s Dairyman notes that in maize silage with this odour, yeasts themselves are often no longer present. Rural News links the smell to silage that has been exposed to air after opening and describes it as a precursor to rapid heating and losses. If a clamp face starts to smell of nail polish, check its temperature and consider increasing the rate at which you remove silage from it.

Sharp and Sweet: Propionic Acid

A sharp, sweet smell with a normal colour often means higher levels of propionic acid. Hoard’s Dairyman links it to forage that was low in sugar or to silage treated with a propionic acid additive. Propionic acid has strong antifungal properties, so in treated silage this smell is expected and usually harmless.

Ammonia: Protein Breakdown

An ammonia smell means a significant share of the crop’s protein has been broken down. This can happen during a slow or clostridial fermentation, when the pH stays high for too long, or during heating. Ontario’s guidance treats ammonia nitrogen above 12 to 15 percent of crude protein as a concern, and notes that the extra rumen-degradable nitrogen can complicate ration balancing for dairy cows. Rural News adds that cows usually reject strongly ammonia-smelling silage.

Caramel, Burnt Sugar or Tobacco: Heat Damage

These smells come from the Maillard reaction, the same browning reaction that gives toast and roasted coffee their flavour. In silage, it happens when trapped oxygen allows microbes to generate heat. Hoard’s Dairyman links it to temperatures above about 120°F (49°C), with silage turning dark brown to black. Typical causes include slow filling, poor compaction, over-mature or over-dry forage and long chop length.

Cattle often eat tobacco-smelling silage readily, which can be misleading. Heat damage binds protein to fibre, making part of it unavailable to the animal, and the sugars consumed in the heating are lost energy. A laboratory can measure the damage as acid detergent insoluble nitrogen (ADIN), sometimes reported as ADF-CP. If you notice this smell, it is worth testing before relying on the silage’s apparent protein content.

Musty, Mouldy or Earthy with Heat: Aerobic Spoilage

A musty, mouldy smell, often with visible mould and heating, means oxygen has reached the silage. Ontario’s guidance lists poor packing, slow filling, low moisture, poor sealing, slow feed-out and poor face management as causes. Hoard’s Dairyman also describes an earthy smell with heating, linked to Bacillus bacteria that follow yeasts once air enters. Visibly mouldy silage should not be fed, since moulds reduce palatability and some can produce mycotoxins; our article on mould prevention silage additives explains that risk in more detail.

Typical Fermentation Values Behind the Smells

Smell tells you what to suspect; a fermentation analysis tells you how serious it is. Ontario’s guidance gives typical ranges for well-made silages, shown below as a percentage of dry matter, except ammonia nitrogen, which is expressed as a percentage of crude protein.

Measure Corn Silage Legume Haylage (>65% moisture) Grass Haylage
Acetic acid 1-3% 2-3% 1-3%
Butyric acid 0% <0.5% 0.5-1.0%
Ethanol 1-3% 0.5-1.0% 0.5-1.0%
Ammonia-N (% of CP) 5-7 10-15 8-12

If the lab results fall well outside these ranges, they confirm what your nose suggested and help you decide how much of that silage to feed. For pH targets by dry matter, see our guide to the ideal silage pH, and for what a high pH usually indicates, see bad quality silage pH.

Smell and Colour Together

Checking silage quality by smell, colour and pH to identify butyric, acetic, yeast or heat-damaged fermentation

Colour adds useful confirmation. Well-fermented grass and legume silage is usually olive green to light brown, and maize silage light green to yellowish-brown. A bright yellow colour with a strong vinegar smell points to an acetic fermentation. Yellow-green or brown, slimy silage with a rancid smell points to clostridia. Dark brown to black silage with a caramel or tobacco smell points to heat damage. White, blue, green or black patches of mould with a musty smell point to aerobic spoilage.

Texture completes the picture. Good silage holds its structure, while clostridial silage often turns slimy and heat-damaged silage can feel dry and brittle. If silage feels warm at the face, oxygen is getting in, and the smell will usually confirm whether yeasts, moulds or both are responsible.

What to Do When Silage Smells Wrong

A bad smell does not always mean the silage must be thrown away, but it should change how you use it. First, send a representative sample to a forage laboratory and ask for a fermentation profile alongside the usual nutrient analysis, so you know the actual levels of butyric acid, ammonia nitrogen and heat damage. Second, match the silage to the animals: keep butyric and heavily yeasted silage away from fresh and high-producing cows, and feed it, if at all, in limited amounts to less sensitive stock such as dry cows or older heifers, mixed with better feed.

Third, remove and discard visibly mouldy, slimy or hot silage rather than mixing it into the ration. Fourth, if the problem is heating at the face, increase the daily feed-out rate and keep the face tight and clean, since every day a layer is exposed to air gives yeasts more time to work.

How to Prevent Off-Smells Next Season

Most silage smell problems trace back to a small number of causes, and each has a practical fix.

  • Butyric smells: keep soil out by setting mowers and rakes high, avoid harvesting very wet grass, and wilt to the right dry matter. Our guide to grass silage moisture sets out targets for clamps and bales.
  • Yeast and alcohol smells: fill and seal quickly, pack firmly, and consider an inoculant designed to improve aerobic stability.
  • Heat damage and caramel smells: avoid ensiling over-dry or over-mature forage, keep chop length appropriate, and exclude air immediately.
  • Mouldy smells: seal completely, protect bales and sheets from damage, and feed out fast enough. Our guide to plastic baler wrappers you can rely on explains film layers and the cost of small holes.

For baled silage, the quality of the seal is often the deciding factor. Silopak, the trading name of Tsingtao Jummos Agricultural Technology Co., Ltd., has manufactured silage consumables in Qingdao since 2011. Our virgin LLDPE silage film is 25 microns thick with a 12-month UV guarantee, and our SD-705 silage additive combines Lactobacillus buchneri, L. plantarum and Pediococcus pentosaceus to support a fast pH drop and better aerobic stability, which directly targets the yeast and heating problems behind many off-smells.

Frequently Asked Questions about Silage Smell

Q: What should good silage smell like?

Good silage usually smells mild, slightly sour or faintly earthy, sometimes with a light vinegar note. Lactic acid, the main product of a good fermentation, is nearly odourless, so strong smells of any kind are more often a sign of a problem than of quality.

Q: Why does my silage smell like vomit or rancid butter?

That smell comes from butyric acid produced by clostridial bacteria. It usually follows soil contamination or ensiling grass or legumes that were too wet. Butyric silage has lower energy and protein value and poor palatability, and high intakes are linked to ketosis in dairy cows, so keep it away from fresh and high-yielding cows.

Q: Is a vinegar smell in silage bad?

Not necessarily. In silage treated with a Lactobacillus buchneri inoculant, a light vinegar smell is expected and improves stability after opening. In untreated silage, a strong vinegar smell points to an inefficient fermentation with more dry matter loss, but the silage is usually still safe to feed.

Q: Is sweet or fruity-smelling silage good?

No. Sweet, fruity, alcoholic or butterscotch smells usually indicate yeast activity, which wastes dry matter and makes silage more likely to heat after opening. Many people mistake these smells for a sign of quality.

Q: My silage smells like tobacco and the cows love it. Is it fine?

Cows often eat tobacco- or caramel-smelling silage readily, but the smell indicates heat damage. Part of the protein becomes bound and unavailable, and energy is lost. Ask a lab to measure ADIN or ADF-CP before relying on the silage’s protein content.

Q: Is it safe to sniff silage?

Take care. Some silages contain spores that can be harmful to people. Place a sample on a flat surface and waft the air towards your nose rather than inhaling deeply from a handful.


Reviewed by Sue Su, Marketing Director of Silopak, on 21 November 2026. Smell is a quick first check, not a diagnosis; confirm any suspected problem with a laboratory fermentation analysis.