
Wood chips have a good environmental reputation, and much of it is earned. A pile of chipped branches that would otherwise be burned in the open or left to rot can become mulch that protects soil, bedding that keeps animals dry, compost that feeds a garden, or fuel that heats a building. Turning waste wood into something useful is a sound principle, and wood chips are one of the simplest ways to put it into practice.
The phrase “save the earth” deserves some care, though. Wood chips are not automatically green. Burned as fuel, they release carbon dioxide and fine particles; stored badly, they heat up, lose value and can catch fire; dug into soil fresh, they can starve plants of nitrogen for a season. Whether wood chips help the environment depends on where the wood came from, what it is used for, and how it is handled.
This guide covers the main uses of wood chips, the real environmental benefits and limits of each, how to store chips so they do not spoil, how to compost them faster, and when baling and wrapping wood chips actually makes sense. It also corrects several points that appeared on an earlier version of this page.
Where Wood Chips Come From
Wood chips are produced by feeding branches, tops, small logs or whole stems through a chipper, which cuts them into pieces typically a few centimetres long. The material comes from several sources, and the source matters for both quality and environmental impact. Forestry operations produce tops, branches and thinnings left after harvesting or thinning. Sawmills produce off-cuts, slabs and edgings alongside sawdust and shavings. Tree surgeons and arborists produce large volumes of chipped branches from pruning and felling in towns and gardens. Some farms also grow short-rotation coppice, such as willow or poplar, specifically for chipping.
Chips from these sources are very different products. Arborist chips usually contain a mix of wood, bark and green leaves, which makes them excellent for mulch and compost but poor for boilers. Clean, debarked chips from stem wood are what most biomass boilers need. Bark, sawdust and shavings are separate materials again, and the earlier version of this page used “wood shavings” and “wood chips” as if they were the same thing; shavings are thin curls produced by planing, and they are mainly used as animal bedding rather than as mulch or fuel.
Use 1: Wood Chips as Mulch
Mulching is the use where wood chips most clearly benefit the environment. A layer of chips on the soil surface reduces evaporation, so soil stays moist for longer and plants need less watering. It shades out many weed seedlings, which reduces the need for herbicides or hand weeding. It evens out soil temperature, protecting roots from summer heat and winter cold. As the chips slowly break down, they feed fungi, earthworms and other soil life and add organic matter to the topsoil.
Arborist chips, with their mix of wood, bark and leaves, are generally considered one of the best mulches for trees and shrubs. A layer of roughly 5 to 10 cm (2 to 4 inches) is the range most commonly recommended. Keep the mulch pulled back a few centimetres from tree trunks and the stems of shrubs, because a mound of moist mulch against bark encourages rot and gives rodents shelter to chew the bark.
One concern comes up constantly with wood chip mulch: that it “steals” nitrogen from plants. The truth is more specific. Microbes breaking down fresh wood need nitrogen, and they take it from their immediate surroundings, which can briefly reduce nitrogen available to plants. When chips sit on the soil surface as a mulch, that tie-up happens mainly in the thin layer where chips meet soil, and established trees and shrubs, whose roots go much deeper, are rarely affected. The real problem occurs when fresh chips are dug into the soil, especially in vegetable beds and around seedlings, where the nitrogen demand of decaying wood competes directly with young roots.
Use 2: Wood Chips for Erosion Control
Wood chips have long been used to protect bare soil on slopes, construction sites, trails and newly planted areas. A layer of chips breaks the impact of raindrops, slows runoff, and holds soil in place while vegetation establishes. Because chips are coarse and interlock, they tend to stay put better than fine materials such as sawdust, which can wash away or form a crust.
For erosion control the same principles apply as for mulch: a reasonably even layer, enough depth to cover the soil completely, and care on very steep slopes where chips may slide in heavy rain. Chips are a temporary measure in most cases. They protect the soil until plant roots take over the job, and they slowly break down into the soil as they do.
Use 3: Wood Chips as Animal Bedding
Wood products are widely used as bedding for horses, poultry, cattle and small animals. Shavings and sawdust are the most common, because they are soft, absorbent and relatively dust-free when produced for the purpose. Coarser wood chips are used in some outdoor systems, such as winter pads and loafing areas for cattle, where they provide a dry, free-draining surface over mud.
Bedding is a practical use for wood that has no higher-value outlet, and used bedding can then be composted and returned to land, which keeps the carbon and nutrients cycling. Wood bedding does have trade-offs. A Finnish study comparing peat with wood shavings for horses found ammonia levels six to eight times higher in the shavings stalls, a reminder that bedding choice affects air quality in the barn. Our guides to peat moss, miscanthus and crop residues compare other bedding materials.
Use 4: Wood Chips as Biomass Fuel
Wood chips are burned in biomass boilers to heat homes, farms, schools and industrial sites, and in larger plants to generate electricity. Chips are easier to handle automatically than logs, which makes them well suited to boilers that feed themselves from a hopper. For many rural sites with a local supply of wood, chip boilers offer a way to replace heating oil.
Moisture is the factor that decides whether chips make a good fuel. Water in the wood has to be boiled off before the wood burns, so wet chips deliver much less useful heat. Based on figures from a Forest Research energy assessment, dry wood has a net calorific value of about 19 MJ/kg, falling to roughly 13 MJ/kg at 30 percent moisture and about 9 MJ/kg at 50 percent. Freshly cut wood is often around 50 percent moisture, which means a tonne of green chips carries less than half the useful energy of a tonne of fully dry wood. The earlier version of this page said wood chips have a “high energy content”; per tonne, they actually carry less energy than coal or oil, and much less when wet.
Wet chips also burn less cleanly. Incomplete combustion produces more smoke and particles, and many boilers are designed only for chips below a specified moisture content. Buying chips by energy content, or by moisture-corrected weight, rather than by volume or wet weight, protects buyers from paying for water.
Are Wood Chips Really Better for the Climate?
This is where the “save the earth” claim needs the most care, because the evidence is genuinely contested. The case for wood fuel rests on the carbon cycle. Trees absorb carbon dioxide as they grow and release it when they burn, so if harvested forests are replanted and regrow, the carbon released can be reabsorbed over time. Forest Research, the UK’s forestry research agency, states that using wood from sustainably managed trees reduces net CO2 production, with only small amounts released through processing and transport.
The case against focuses on timing and source. At the point of combustion, wood emits more carbon dioxide per unit of energy than most fossil fuels. A Chatham House analysis cited figures showing about 13 percent more CO2 per unit of energy than coal at one UK power station, and argued that regrowth can take decades or even centuries when whole trees are harvested and burned. On this view, burning wood adds carbon to the atmosphere now and only pays it back slowly, if at all.
Both sides agree on an important middle ground. Residues that would otherwise decay quickly, such as sawmill off-cuts and post-consumer waste wood, give the clearest climate benefit when used for energy, because their carbon would be released soon anyway. The same analysis noted, however, that sawmill residues are already almost fully used, so there is limited room to expand. Burning whole trees, or wood that could have gone into long-lived products such as timber for buildings, is far harder to justify. The practical rule many analysts arrive at is “use it, don’t burn it”: keep wood in long-lived products where possible, and burn only what has no better use.
Air quality is a separate issue from climate. Burning wood releases fine particulate matter (PM2.5), which harms human health. Defra reported that domestic burning, which includes wood stoves and open fires, was the largest single source of UK PM2.5 emissions in 2019, at around 43 percent. The earlier version of this page said wood chips burn “without polluting the environment”; that is not accurate. Modern, well-maintained biomass boilers burning dry fuel are far cleaner than open fires and old stoves, but no combustion is pollution-free.
Storing Wood Chips So They Do Not Spoil

Storage is where much of the value of wood chips is lost, and the problems all start with moisture. Wet chips in a pile heat up as fungi and bacteria begin breaking them down. According to COFORD, Ireland’s forestry research advisory body, a pile at 45 percent moisture can reach 60 to 80°C within about 24 hours, and elevated temperatures can persist for weeks. That heat consumes the wood itself: normal forest chips above 35 to 40 percent moisture can lose about 1 percent of their dry matter per month, and very wet, nutrient-rich chips such as short-rotation willow can lose more than 3 percent per month.
COFORD’s guidance on storage time by moisture content is clear:
| Chip Moisture Content | Indicative Storage Period |
|---|---|
| 0-15% | Very long periods, several years |
| 16-25% | Several years |
| 26-35% | Up to a year |
| 36-45% | Months |
| 46% and above | Days to weeks, one month at most |
For storage beyond two to three weeks, COFORD recommends keeping moisture below 35 percent, excluding needles and leaves, avoiding compaction, keeping piles small and regular in shape, and using the oldest chips first. Irregular piles let rainwater collect in hollows, which raises local moisture and encourages self-heating; wood itself self-ignites at around 250°C, and large, compacted or poorly ventilated piles are the ones most at risk of fire.
Health is the other storage hazard. Heating chip piles grow moulds whose spores can cause allergic alveolitis, often called “farmer’s lung,” which worsens with repeated exposure. COFORD recommends a P3 filter mask, or a tractor or loader cab with equivalent filtration, when handling stored chips, and advises ventilating enclosed chip silos before entering and never working in one alone.
Composting Wood Chips Faster
For mulch and fuel, decomposition is something to avoid. For compost, it is the goal. The earlier version of this page treated decomposition as a step that should happen before any use, which mixes up these purposes. If you want wood chips to become compost, three changes speed the process up considerably.
The first is particle size. Smaller pieces have more surface area for microbes to work on, so running chips through a shredder a second time, or using finer chips, shortens the time needed. The second is nitrogen. Wood is high in carbon and low in nitrogen, and microbes need both, as research on microorganisms decomposing wood shows. Mixing chips with nitrogen-rich materials such as grass clippings, fresh manure, used coffee grounds, kitchen vegetable waste or comfrey leaves gives microbes what they need; in larger operations, a nitrogen fertiliser such as urea or ammonium sulphate can be used. Bark, despite being part of the tree, is carbon-rich “brown” material rather than a green nitrogen source.
The third is air and moisture. Turning the heap every couple of weeks introduces oxygen and keeps the decomposition aerobic, and the heap should be about as moist as a wrung-out sponge. Composting is fastest in warm weather, but turning a heap in winter does no harm; it is simply slower. Wood chip compost typically takes longer than compost made from soft garden waste, so plan for months rather than weeks.
Baling and Wrapping Wood Chips: When It Makes Sense
The earlier version of this page suggested that wood chips are routinely baled and wrapped in silage film before any use, and that the plastic “preserves the wood.” Most wood chips are never baled. Fuel chips are usually stored in covered heaps, bunkers or silos and moved in bulk trailers; mulch chips are often delivered loose straight from the chipper; and smaller quantities are sold in bulk bags or sacks.
Baling does have a real role for some wood products, though. Compactors made by companies such as Orkel can compress wood chips and wood shavings into dense round bales and wrap them. According to Orkel, baled shavings at 80 to 90 percent dry matter are easier to handle and transport, can be stored outdoors while staying clean and dry, and carry a lower fire risk than loose material. Round bales of chips are also denser than loose chips, so more tonnes fit on each truck.
The key word is dry. Unlike silage, wood chips and shavings are not preserved by fermentation. Wrapping keeps dry material dry, clean and contained; it does not rescue wet material. COFORD’s guidance against storing chips above 45 percent moisture for more than a few weeks still applies, so chips intended for long storage or baling should be dried first. Baled, wrapped wood products are best suited to bedding, shavings and dry fuel chips that need to be transported or stored outdoors.
Silopak Wrapping Products for Baled Materials
Silopak, the trading name of Tsingtao Jummos Agricultural Technology Co., Ltd., has manufactured and exported baling consumables from Qingdao since 2011. Our core products are designed for forage, but they are also used on other baled materials. Our 100 percent virgin HDPE, UV-stabilised bale net wrap comes in 0.52 m, 1.05 m, 1.23 m and 1.25 m widths, with a guaranteed minimum of 2,000 m per roll. Our virgin LLDPE silage film is 25 microns thick, supplied in 750 mm × 1,500 m, 500 mm × 1,800 m and 250 mm × 1,800 m rolls, with a 12-month UV guarantee.
If you bale wood shavings, dry chips or other bedding materials, check your compactor’s film and net specifications first, since some industrial compactors use different film widths from agricultural bale wrappers, and talk to our team about matching our products to your machine. Balers and bale wrappers are produced by our group company; the combi baler wrapper range is at jummos.com.
Frequently Asked Questions about Wood Chips
Q: Are wood chips good for the environment?
It depends on the use. As mulch, wood chips clearly help: they conserve soil moisture, suppress weeds, protect soil from erosion and feed soil life, while putting waste wood to good use. As fuel, the picture is more mixed. Residues that would decay quickly anyway give the clearest climate benefit, but burning whole trees can add carbon to the atmosphere for decades, and all wood burning releases fine particles that affect air quality. Using wood in long-lived products first, and burning only what has no better use, is the most defensible approach.
Q: Do wood chips rob soil of nitrogen?
Only in specific situations. Microbes breaking down fresh wood use nitrogen from their immediate surroundings. When chips are used as a surface mulch, that effect is largely limited to the thin layer where chips meet soil, so trees and shrubs with deeper roots are rarely affected. The problem arises mainly when fresh chips are dug into the soil, particularly in vegetable beds or around young plants. Keep fresh chips on the surface, and compost them first if you want to incorporate them.
Q: How long can wood chips be stored?
It depends almost entirely on moisture. COFORD guidance indicates that chips below 25 percent moisture can be stored for several years, chips at 26 to 35 percent for up to a year, chips at 36 to 45 percent for months, and chips above 45 percent for only days to weeks. Wet chips heat up quickly, lose dry matter and can self-ignite in large piles, so they should be used fast or dried before storage.
Q: What moisture content should wood chips be for a boiler?
Check the boiler manufacturer’s specification, since boilers differ. As a general principle, drier chips give more useful energy and burn more cleanly. Dry wood carries roughly 19 MJ/kg of net energy, falling to around 13 MJ/kg at 30 percent moisture and about 9 MJ/kg at 50 percent, so green chips deliver less than half the heat per tonne of fully dry wood. Buying chips on an energy or moisture-corrected basis avoids paying for water.
Q: Should wood chips be wrapped in plastic?
Usually not. Most wood chips are stored in covered heaps or bunkers and moved in bulk. Wrapping makes sense mainly for compacted bales of dry wood shavings, bedding or dry chips that need to be stored outdoors or transported, where the wrap keeps the material clean and dry and reduces fire risk. Wood chips are not preserved by fermentation, so wrapping does not rescue wet material; chips should be dried before long-term storage or baling.
Reviewed by Sue Su, Marketing Director of Silopak, on 29 October 2026. The climate effect of burning wood is still debated, so the figures here are presented with their sources rather than as a final verdict.
